toyota

Trying this over here instead of the general newb section. :homer: They are half the price of replacing with trail gear,(speedway price is $160-ish) and specs are 3.0 gpm and 1200psi. They have a tapped suction port with AN fittings so they should be a direct bolt in replacement for the ten+...

92 pickup, SAS, 3.4, R150, duals Have been gathering parts for my swap from SAS w/ TG housing to links with 4WU kits and Diamonds. I have most everything now except the rear link parts from 4wu but now I lost my guy that was going to install everything. I don't have the know-how, the...

I’ve been having a rough idle/ rough initial startup on my 98 4Runner 3rz 5 speed 168000 miles. Did a compression check and I’m at 215 psi for cylinders 1,2,&4. Cylinder 3 is at 80 psi. Did a leak down test and it’s the exhaust valve on that cylinder. I’ve been running it with this...

I"m running Bilstein 5150's and stock coils and stock LCA/UCA on my taco with 285's. The alignment shop says I need adjustable UCA's. It has some pretty bad negative camber. This rig gets 'wheeled' daily on a 7 mile long, steep, rutted out, snowy/icy dirt road daily. Looking for some budget...

First time setting up a 3rd member, pinion shimmed at .085" Aftermarket V6 housing, 4.88s, Spool Seems like it's a bit too deep? Thoughts? Send it? Take out a shim? Go fuck myself?

sirch failed to produce an answer to this, So that said besides fail gear does anyone make d.l. spacers for r1f geardrive t cases? I know retube it...

I am looking into a DUI distributor for my truck. Are they worth the cost over stock? My truck is a 222R with a Got Propane setup, an engine builder RV cam and LCE header.

Currently running a stock 2RZ power steering pump. I'm familiar with the "Stage 1-3" pressure, flow, and inlet mods to 22R pumps but I'm honestly not sure if this would apply the same to the 95-00 2RZ/3RZ pump. The complete pump is a 44320-04020... It shares the same base pump housing...

Buddy of mine put a new motor in an 87 pick up. It's a 4x4 5spd if that matters. The throttle cable bracket was a bit of a mystery, but I thought we got it. Now he's saying that it's not right as it only goes half throttle. Anyone have a Pic of their throttle bracket or any idea why it would...

I looked but didn't find any dimensions comparing the two. Dual toy cases makes for too much tube rework in my buggy and the current single 4.7 isn't low enough. The dana/toy combo looks damn close dimension wise to a single toy case.

Brain has both options on his site and I am not sure the pro's vs. con's of each. Yep, I could call and ask him but just seeing what everyone here thinks..........then I will do that. :flipoff2: 92 pickup, 3.4, 150, duals, 4WU front

Need 5.29s. Spend the money on Yukon for 300 or g2s from summit for 170. Whose making good budget gears these days? Any brands to steer clear of? A friend got a used set of old school built axles. They had OG longs in them old, and when we pulled them a part, the ring gear has 2 teeth...

any body here have any issues with yota one performance down in riverbank CA? buddy of mine is having some issues with a new motor from them, just wondering if its a fluke or the norm?

good afternoon, so i had to mount my ignition on passenger side of the engine bay and the coil wire is way to short, i did find one universal plug wire at a parts store in town but it worked but not great, feels like they will fall off. maybe it was my way of doing the universal but this kit...

Is there an easy way to identify OEM Aisin hub gears versus aftermarket chromoly hub gears, once both have been in the hubs and used enough to not look new anymore? I can't find any info about the OEM gear material so comparing hardness or density may or may not work.

My IFS hubs on my van (same as any pickup/ runner 86-94?) need new gaskets and o-rings. Anyone have a decent source for these?

good am are you on here, if so how did this thing do? link to video

good am, can i mount my power steering res on the passenger side of the engine compartment and just run a hose to the pump, i had it here witch it was nice because it was right above the pump, but i have now mounted the turbo and everything in this spot . PS.... i hate this res with a...

Hey I'm getting ready to stitch weld some plate to my frame for a repair, what should I use to seal the seam between the plate and the frame?

I've been running 39.5" Rockers for years, but am contemplating a move to 40" Trep stickes to keep with the Jones' - er, my wheeling mates, who are running 42" Reds and Treps. I'd love to do it, but much prefer wheeling to breaking stuff, and so could keep running what I have. What say you...