toyota

88 4Runner. Doesn't look stock, but the fuel system largely is: Stock tank in stockish location (may raised 1"), stock charcoal cannister in stock location. The original vent hard line to the cannister used to clog up and create tons of pressure in the tank. I finally just replaced that hard...

My 98 4Runner is whining like a liberal, and with 240k on it, they should probably be replaced. At the old site, I did a non-scientific poll (this for 8" gears), and US, Motive, Genuine, etc., all came out about the same for amount of breakage. How 'bout now, Nitro's OK?

I bought this truck used with about 200k on it, was in great shape - no oil leaks, no check engine light but needed to do brakes and tires and water pump. About 300k, I got hit by a kid in his moms minivan and decided to sell it to a buddy and buy a brand new Tundra. He did all the ball joints...

I have an 83 with factory air, the dash switch died. The fan works but the cooling control don't. The switch is nla, thinking about cutting up the stock dash is a nogo! I'm thinking the cooling control from a second gen dash may work out, it's a 2 wire slider if I recall?! Got a pic of the dash...

Auxiliary emergency parking brake FJ 40 I need to install an aftermarket emergency parking brake 1974FJ 40 with Danny Warden conversion Disc brakes 1978 rear calipers 1982 forerunner front calipers Please advise Any info greatly appreciated Just jumped over from pirate didn’t realize they...

Alright, I have spent about an hour googling and searching forum boards, and cant find this info... So let's get it here for future shit! I am looking for the bolt size and length of the FJ80 Knuckle/Spindle/Backing Plate bolts... It is part number 90101-10166. I am guessing it is M8x1.25 but...

Ok I am working on a 1st gen Tacoma 2wd Prerunner truck. I am going to be swapping to a steering box and doing swing set steering and a ram assist to reliminate the weak factory rack. Now my question is what spline does the 1st gen Tacoma steering racks use? Thanks

Ended up with a set of 2.8/2.8 cases. Marlin Adapter with a TG V6 adapter on the front. Going to take the V6 adapter off and try to sell that separately. What is the going rate to sell the cases with the Marlin adapter? I haven't been into the used part market in a while. $550 with shifters...

Doing a timing belt and water pump. My last pump used a paper type gasket that I just used a little sealant on. This one is a factory Toyota metal gasket with a thin rubber gasket molded around the whole thing. Do you guys still use something on this type of gasket or put it on dry. My manual...

I am sure this has been done a ton, but I can't seem to find the info anywhere (here, mud, old pirate, etc). So posting it here to live on in infamy. If you are taking a custom builder axle housing and cutting it for an fj80 axle shafts and 8"hp third: The cut for the Long side will measure at...

Picked up this 2nd gen “truggy” project from a buddy of mine this truck has been owned by a few buddy’s and has never been finished so I’m hoping I can finally get it out on the trail. Should be a cool little project plans as of right now are to throw my 22re that is boosted on propane in it...

The seal/O-ring on the speedometer connection of my dual transfer case is leaking. Might any of you have a part number for what I need? It's a gear drive case, of course, circa 1985. I've found LC parts, but I don't know if those use the same case or, if not, if the LC seal would fit. Mark

Local FJ40 we are picking up. More to come 🔥

Idk why I'm having a hard time finding a replacement cap for the power steering reservoir Just a stock one for an 86 4runner 22re When I Google search it a bunch of things pop up but they're either for 90-95 3.0s which look different or just a generic cap pops up in the search that doesn't...

This concept was at the Space Symposium. It uses four Rav4 EV motors. Videos on dirt were impressive with full size rubber tires. Michelin wheels large enough to clear the brakes were not yet available. Here is a link to that technology.

-LS swap -FJ80 axles and radius arms, SOA rear Way back a long time ago, May 31 2016, I drug this pile home: Much like my thread about The Possum Catcher, I have a truck with a story. Similar to that truck, this one has allowed a simple repair to spin out of control and into a project...

I just bought 37x12.5r17s and some rims that are 9" wide, -12 offset, which is about 4.5" back space,(according to online calculators). Doing a bunch of research everyone typically runs 3.75" back spacing it seems, but is that necessary for clearance or just to get a wider stance? I will use...

Lost my clutch the other day. Turned out to be the wimpy mounting bracket that the clutch and brake assembly mounts to. Pulled it out , what a PITA, and found this. The part was about $200 so I figured I would try to repair it. Worked it back into shape, ground out the cracks and welded it up...

Well, I can’t seem to help myself… Last weekend I picked this up from buddy of mine. First the good stuff! Here are the specs: 1994 4Runner SR5 with about 206k miles. 3.0 V6 that had the HGs done approx. 15k miles ago. A340H auto trans. Dual RF1A t-cases, stock geared, RADesign triple...

First thread,First "Crawler", and my First Build! So bare with me :flipoff2: Never documented and interacted on forums that share the same story so here we go! #polishingaturd Ill be also trying to revisit past dates to show timeline of the build. Equipped with on purchase Typical Toyota...