jeep

Have several parts sitting in the garage that need to go to declutter - Hopefully useful to someone here. Originally purchased for an 88 YJ w 4.2L Engine Purolator F21117 Fuel Filter Purolator PV1008 PCV Valve Purolator B13153 Crankcase Breather Filter Carquest FL3 Carburetor Float Borg Warner...

Whats the state of the art on this? Is anyone in the world tuning out the ridiculous egr and dpg of the jeep ecodiesels? I have an idea to emulate sensors, but would like to know what has already been tried or why that might not work.

I’m starting to work on my Tj project and plan to attempt a build thread. Plan is 110-112 wheel base with as much of the stretch to be in the rear as possible. It’ll be built on gm 60 front sterling 10.25 rear. Dual triangulated with 14in kings front rear. I bought the rig from a friend...

Has anyone installed a Premier Power Welder on there JL or JT??

Dragging this build thread from P4x4.... Its now going back under the knife for rear stretch w/ trailing arms, upping the 5.3 to a chop cam'd L86 6.2. I bought this jeep when I was 15 and have been steadily hacking it up Old thread starts below -

So this started a few years back... September of 2016 in fact. A childhood neighbor mentioned he was selling this jewel, and since the price was wrong, and it was rusty, I said yes. She's freakin mint Boyz. Fleeeexxxxxx for days. Next to my last XJ... Never should have sold it...

Dirty but complete minus shifter stuff. 6spl bull Drive shaft Saved it from getting scrapped. No need for it. Nw of redding ca.

Found a 05 4:1 tcase that the front out put is cracked. Just curious if this is worth anything. There is supposed to be a diy eco box available soon that would use these planitarys. I've always thought a 4:1 crawl in front of a 205 was the perfect ratios. Unless someone here needs it?

Decided to make a post on some upgrades this off season to my family’s racejeep. Been a long time lurker on the old site and this one, never felt I had anything worthy of posting. Quick background, I have been racing Jeeps with the PNW4WDA since I was in the fifth grade. My wife and I bought...

I know that amount of work required to accomplish both the Rear and Front Axle Stretches, so I am not looking for which one is easier or which one is more cost effective, best bang for buck, which you would prefer to do, etc..... I am looking at actual benefits from a wheeling perspective. From...

Hey guys, researching an sm 465 swap into my yj, gonna do a 5.3, doubler and a Ford 205 with a super duty front, my question is with the bell housing, would love an external slave cylinder, but I'm worried about interference with the front driveline. I'm doing the full width kit from motobilt...

Two questions: 1. What's the physical difference between 2003-2004 vs 2005-2006 TJ/LJ 42RLE transmissions? Online and local shops says they are not interchangeable, but it appears they run the same valve body and solenoid pack. I want to build a spare trans to have for both my 2004 and 2006...

I have a welded roof rack left over from a previous rig that I’d like to use on my TJ hard top. Don’t want an exo-cage or any of that. Don’t have good options for drip rail mounting. And I’d rather not drill holes in my cherry hard top. But this seems like the best option. The rack is -4’x5’...

Anyone have a disc D30 handy? What's the measurement from center of top BJ to wheel mounting surface?

So, a couple of years ago I built a full ground up trail rig. DJ5, tons, 40s, ORIs, fuel injected SBC. Beat the hell out of it for the past couple years, no issues other than a broke stock 78-79 KP60 inner shaft and a driveshaft sheared after I dorked it on a sharp rock. The thing does every...

Buddy just got a 92 yj. 4.0 5spd. Starts cold, dies after 30 seconds or so and won't start again. Replaced- Coil Distributor Crank position sensor Fuel pump Swapped the ASE relay with the horn, no change. Fuses are all good. Code says intermittent crank position sensor fault, wire harness...

I am going to try my hand at a build thread. Unfortunate its nothing crazy, just a resto mod. I've been on this site and the old site for a bit and have done everything but body work, so this could be interesting. Wife is currently going back to school so progress maybe slow. Lots of time...

so has anyone felt the need for a transmission skidplate? and howd you make one?

I started this build over 5 years ago. Lots of things got in the way of finishing it but I have decided to finally get it done. I am a newbie with respect to building a rig like this. I appreciate any advice/criticism you fucking fucks have :flipoff2: It’s a 1996 XJ 4.0 w/aw4. KP 60 front...

Hey guys. Bought this YJ over the summer from a dude in Atlanta. It's an 88 (I think). Has a 5.3, 4l60, np241 for drivetrain. Axles are a hp 44 front and 60 rear. Lockers front and rear with rcv fronts and 35 spline Yukons in rear. It wheels good but the XJ springs in the rear with a...