ford

  1. Ford Power Steering Line Experts I need Help

    Swapping my 79 ford onto a 2006 Super Duty frame, details here: Buford 79 Ford My power steering to hydroboost lines are about 6" short, and I figured the best route was to just get the correct adapter from the Box, pump and hydroboost to JIC fitting and make my own lines, the idea being that...
  2. Gbkeith

    Red Excursion Thread

    Some of you who don’t have better things to do with your time may have seen my thread in chit chat picking out an excursion because my wife wanted more interior room. The thread discussed marriage and female behavior without talking about tits, so we basically became feminists. After that we...
  3. Covecrawler

    VA Rear axles. Ford 9”, dana 60, dana 61, Sterling 10.25. $100 each . 14b C&C $250 14b SRW $200 Winchester, VA

    I have around 20 axles total to sell. I bought them out of a field. Some have some water and rust. Most seem to be ok. Will need standard seals, bearings, brakes. 2) 4.10 C&C 14 bolt Chevrolet axles $250 each 1) 4.10 SRW 14 bolt. square body. $200 2-3) 3.54 Sterling 10.25 $100 each 1) dana 60...
  4. CA 1990 Ford F350 Front Spring Plates

    Looking for front spring plates for a 1990 F350 D60 front axle. Let me know what you have
  5. Mvanhelden

    CA 78-79 Ford Dana 60 Front

    Have for sale a 78’ Ford Dana 60 I rebuilt for a project years ago, never finished the truck and parted it. It’s got new 4.10 gears, new Kingpins and studs, Ballistic Fab springless high steer arms with tie rod, good condition Spicer hubs, new bearings seals and brake calipers/pads. The hubs...
  6. 2017 Ford Edge Sport Limp Mode

    I know this isn’t exactly a 4x4 vehicle, but I am pulling my hair out over my daughter’s car. It is a 2017 Ford Edge Sport is has the 2.7 eco boost. Because Guthrie it thinking she would have something safe and reliable in 2021 when used car prices absolutely sucked. About 6 months after we got...
  7. ManKrawler

    ID bearing in oil pan

    I work on a truck as a favor occasionally, it had a bad starter solenoid so naturally I have removed the oil pan. This bearing is laying in the bottom, cam?: 89 Ford 5.0L in a F-150.
  8. rockota

    NOOB: 7.3 OBS Question

    Passenger side of engine. Rubber drain hose (or... appears to be a drain hose). Trace it back as far as i can, it attaches to a hardline that appears to go behind the tensioner/alternator bracket... that's where I lose it. Trying to figure out what it is... seems to have a drip of ATF... but I...
  9. Captain Call

    Header gaskets

    Which ones are the bestest most greatest these days? 460 with D0ve c heads.
  10. rockota

    OBS side steps

    Need some steps for the OBS. Not going to put the old style diamond plate stuff on this truck. Also not willing to spend the money needed for the Chevy AMP Research steps and adapter kit. I'm thinking $200 total budget. Looking at either a set of chinesium "stainless" amazon specials - knowing...
  11. CDA 455 II

    Converting to hydro-boost; mod'ing pushrod/brake pedal connection & length

    I'm looking to upgrade my '94 Bronco to a '94 F-350 HB set up. So far it appears mod'ing the pushrod/brake pedal length will be my biggest hurdle. What simple way(s) can this nOOB accomplish this mod? My thought for a simple mod is to weld a bracket on the pedal for the pin where the pushrod...
  12. Provience

    E4OD transmission swap

    alright, procrastination continues and now i've got questions. Slowly gathering stuff to swap away from my C6 behind my 400. https://irate4x4.com/threads/1989-f350-7-3l-c6-swap-to-od-trans.377786/ the above thread talks about making the swap behind a 7.3 IDI. 72Pstroke says: granted, i'll...
  13. 1980 Bronco 5.0l valve adjustment

    So got a stock 1980 Bronco 5.0 v8. I need to check push rods for straightness to determine why I'm having a misfire. When doing this do these motors have a set torque spec for rocket arm bolt of like 20 ft lbs or do you have to rotate motor until valve would be closed and tighten to remove...
  14. C.R.D

    51 Rock Crawler Build Build Thread

    Hey everyone, So I have been building my 51 Ford rock crawler for a few years now. This past January there was some significant changes in my personnel life that have allowed me to spend more time building this project. So here is a run down of what I have done and where this is going. The cab...
  15. CA 1985 Ford f250 4x4 Supercab diesel NO SMOG

    1985 Ford f250 4x4 Supercab super cab 4x4. 6.9l Diesel engine, auto trans. Pre smog super cab 4x4 diesel. Does not drive needs trans rebuilt and reinstalled. Was told it was parked 11 yrs ago when trans stopped working. Removed trans and t-case and never did anything to it. Non op so no back...
  16. 1998 Ford F700 ignition switch

    Seems like ignition doesnt work with key on position. It comes on when the key is almost at the crank stage, but goes off when key is returned to ibgition position. Any clue?
  17. Covecrawler

    Ford 3.31 geared dana 61 rear axle

    Bought a heap of axles out of a field. I have no info on what they came out of. 2 of the rears are Ford dana 61s with 3.31 gears. Is there any market for these or scrap metal? I know Dana 60 rear axles are nearly worthless, is the market any different for these obscure axles? I really can’t...
  18. Buford T - 79 Ford Crew Cab Powerstroke Swap

    I've always had a thing for dentside fords. When I was a kid, we had a 77 supercab that I loved. Flash forward 40 years and I've decided its time to own one. I have a pile of 99-07 super duty trucks, and know them well, so the obvious decision for me was to toss a cab on a super duty chassis...
  19. Grendel

    NH Ford - Front 5 bolt spindles and 8 lug hubs - Dana 50 or 60, please

    Don't need them right away, this is to use some weld on flanges I found on a shelf.
  20. Little ween/Big truck Budget coil conversion Ex on 4Ds

    I bought this excursion years ago long before I moved up to Alaska as a tent on wheels. It's a well used high milage v10. I've been eye balling geek 4x4's bobbed excursion thinking it'd be a relatively affordable way to turn this poor old beater into a trail rig to run out to the glacier and...
Top Back Refresh