ford

  1. LScout800

    CA Ford NP435 with FE Bolt Pattern

    Looking for an NP435 to go behind a 390. Preferably 2 wheel drive. Located in Orange County. Would be willing to drive a few hours if the price is good. Going to be putting it in my '69 F-250 to replace the bad C6 that is in it. I would rather have a manual so will be converting it. Other misc...
  2. Tech Tim

    OBS 7.3 Experts Please Step In - Rebuilt Fuel System - Rough Idle

    Finished up doing a fuel system redo on my 1997 OBS F350 7.3 Powerstroke. It starts up and idles smooth for the first 8-10 seconds, then goes into a rough idle. It runs strong off idle, though maybe seems a little light on power at highway speeds. This truck has 375K on the ticker and last...
  3. 4RunnerGuy

    1993 F150 5.0 4X4 PCM

    I have the truck listed in the Title. My son bought as a first truck, he moved on to something else. It's a completely rusted out shit pile. The fact it's OBS and 4x4 enabled me to convince myself it's worth keeping. The worst part of it is the cab roof is pretty well rusted out. NBD, I bought...
  4. OR Ford 302 Edelbrock RPM Air-Gap intake

    Nice intake not beat up not marked up. Retails for over 400. Willing to consider trades for early bronco parts that I can use, but primarily after cash. Location: Klamath Falls, Oregon. Price: $295 Shipping: I will consider shipping if needed after the ad runs for a bit.
  5. IowaOffRoad

    Let's wildly speculate about why a 95ish Ford Ranger I bought was parked!

    Bought an early second generation Ranger (it's TTB with a pushrod 4.0L, sorry I didn't get the year... yet) for scrap price. Good body, 5spd manual, manual shift t-case (IIRC) that's been parked for a decade plus due to unknown to the current owner why. I'd figure blown head gasket/cracked...
  6. Reno Off-Road (Parts)

    Spring Perches | Dana 60 | Ford 8.8 | Ford 9"

    Make your job a little easier with these spring perches. Includes: 2-Perches for one axle Dimensions: Axle diameter: 3 1/4 or 3 1/8" Width: 2.5" This is a new variation on one of our fairly basic items, but it isn't quite that basic. Here's what you want to know: these are .25" (1/4) HR P&O...
  7. cadman929

    Full manual superduty (im really scared of computers)😂

    do you listen to your old alabama tapes in your tow rig on the way to go wheeling? Do you love your old manual fummins? Do you need more room for fat chicks and your dog? Do you need a hp60 to build a new axle for the front of your buggy when you go rear steer? Do you want to be able to go over...
  8. dave_dj1

    09 f250 PO430 code

    09 F250 with the 3 valve 5.4 with 153K, automatic. I just bought it from the original owner. The CEL came on today, code is PO430 which is the catalyst system is not operating properly. P0430 OBD-II Trouble Code: Catalyst System Efficiency Below Threshold (Bank 2) It has had a stumble which I...
  9. 2big bronco

    7.3 clutch and realistic expectations

    2002 7.3 6spd with basic mods and a 15 year old dp tuner. I run the tuner on stock or economy mode 100% of the time. I got the truck at around 170k miles and replaced the clutch shortly after with a southbend 1944-60k I believe.( supposedly 1 step above stock) Truck has 300k on it now and it...
  10. TX 1997 F-250, 4x4, 7.3

    SOLD Extended cab, XLT, 4x4, 7.3l diesel, automatic transmission. Power windows and locks. I have a massive stack of receipts for everything on the truck. Including the original window sticker. Engine is all original and unmolested. I have never towed with it, never tuned. Runs and drives fine...
  11. 9" Tuesday question

    Looking around at yokes and I see there is a difference between the 9" big bearing vs small bearing... As far as the yoke is concerned. What is different between them?
  12. Arickvan

    Ttb steering?

    Y'all ever seen a steering setup like this? I saw it at the hammers this year
  13. Explorer disc brake on 9" ends

    Did some googling, most of the stuff i can find links to dead forums or old guys arguing about why youd bother doing anything but wilwood/ssbc/whatever fancy brake stuff. I'm narrowing an 8.8 for my s10. Going to put ford 9" ends on it. I would like to use the current explorer 8.8 disc brake...
  14. RustyC

    AL Ford 9" / 10" HP gears

    Looking for a HIGH PINION 5.14 or 5.43 ring and pinion set. New or used
  15. CA 67-72 Ford Truck parts

    I'm Lucerne Valley CA about 30 min from the hammers. So get some parts while out wheeling or send friends to pickup for you when they come out wheeling. I have a few ford 2wd trucks I'm parting out. One 69 f100 and one 71 f350. Plus extra doors and fenders. Have body panels available just no...
  16. Poke

    ‘20 paddle shifters

    2020 navigator. My father keeps accidentally grabbing the paddle shifters and dropping gears. It’s dangerous. I assume it’s the same system in all fords Is there a way to turn them off or easily remove them?
  17. MD Ford T-19 4x4 or NP435 PTO

    Looking for either a T-19 4wd or a pto for a NP435. Got a mid 80's F-350 2wd dump truck with 6.9 idi I use around the farm and want to put a 4wd trans is for 2-lo instead of burning the clutch out. Got a Ford 4wd NP435 recently and thought I was set, but then remembered the PTO is trans...
  18. FordFascist

    1989 Ford LGT14D ultimate mower build

    As many of you know, I am a Ford guy. I also needed a riding mower. At this moment in time my backyard was starting to become a fire hazard - my push mower was being a dick and I had already used a reel of .083 weedwhacker line. I was also quoted $800 for someone to come and clean this mess...
  19. DF Fabrication

    Ford Super Duty Parts

    Since were new here figured we let folks know some of the parts we offer. For the Ford Super Duty axles we have a few components that may interest you 99-04 High steer Arms 7075 https://dffabrication.com/store/ols/products/superduty-high-steer-arms-99-04 05+ High steer Arms 7075...
  20. welndmn

    Skyjacker Radius arms DIY Brackets

    It's been a long time since I've had a RBV again, but a year ago I picked up a 1990 Bronco 2. It's only got a 2" puck lift on new coil springs on 33's (well some metric size off a new Jeep JL). The other day I got a Dana 35 from a Ranger and it came with some Skyjacker radius arms, but not the...
Top Back Refresh