ford

What do you get when you cross a van with a truck? A Trans! With that in mind I am building a flat bed and beaver tail on the back of a former Uhaul E-450 cutaway chassis. This truck has 137k miles, V10, 5R110 and a Super 70 rear axle. Should work good!

Seems that 32 spline 1330 yokes are hens teeth. OE or aftermarket. Why? I have one from an unknown year (1980+) it’s a rear ubolt yoke. What am I trying to accomplish? The front shaft in my big ghey truck land truck binds up at the output. (1310 ubolt) The ubolts bottom out hard. It will...

I have some leftover stuff from my 9” project. I bought this case because I thought my other one wouldn’t work with the carrier I had, but, it ended up working. It sat in my garage for a month and so it’s too late to return it. This includes the following: Ford 9” Yukon dropout housing (Model...

So I have a 7.3L ZF-6 with fresh clutch and total rebuild. Also have the 271 that came behind it. It's either 24/34 spline (haven't split the cases yet). I am sticking this behind a 6bt Cummins in my 1941 Chevy G506. I bought a passenger side drop 14B front from TTRAxle&FAB with all the...

Any ideas why most of my braking is on the front, to the point it gets them smoking hot? Rear pads were replaced last year, and I adjusted it this spring which slightly helped. They engage when tested with ass in the air. And park brake holds the truck fine. Pedal travels normal, and effort is...

Hello world, though I share my truggy my kids and I built and this year has been the best, because we final got her out and beat on it out in the mud. It was a long road to get it to this point, my kids got to learn how to weld, rebuild transmission, transfer case, engine rebuild, axle and...

Sold

2012 Ford Raptor 31,538 miles. Completely stock, only addition are some off road lights that are on the upfitter switches that bolt into factory brackets. Runs and drives great, just don't drive it as evidenced by the miles. I have a work truck that I am chained to, so the Raptor only got...

Started off with a 2011 f250 6.2 service truck. Previous state of Ohio emergency services management supervisor truck. Can tell it didnt haul or tow heavy. Had stock 250 springs with a badly sagging ass end. The 3.73 gears left a lot to be desired, even with smaller than stock tires. The goal is...

So I acquired this FSB (Farm Sitting Bronco) that had been sitting for 7 years. It was abandoned at my uncles farm up north, Taft, CA. Pretty much stock, after a couple fuel pumps and a new gas tank and tune up its up and running. I get the bronco in December 2022, it passed smog, me and my...

Starter in my 99 F2Shiity Super Poopy is getting weak. I’d like to replace before it totally shits the bed. What options are available for upgrades? I’ve read 2000-2003 will work. Anything else I’m missing?

I have a few Ford Np205 transfercases. 31spl married cases Complete. Have some adapters for c4 c6 trans as well. Located in Grass Valley, Ca. 94954. $600 each

1989 f350 king pin 60 5spd 7.3 less than 100k unmolested for most part. Ignition and steering column did the usual and then some as far as what goes wrong.. long bed no turbo. Undecided whether it'll get one or not. Solid truck no leaks what so ever .. one owner as well :smokin::usa: Also...

I have this 95 E250 that was my LAX crash pad for 11 years. I'm moving to a new base and I'd like to take this so I have wheels and a place to take a nap if I end up stuck for a night. It only has 170K and runs great and is overall pretty sound, but 11 years sitting under the LAX approach path...

OK, So I have the main and aux tanks and it looks like the Fuel selector valve (Aux/Main) shit the bed.... no fuel from either tanks to the pump, and the tanks are feeding the selector valve. What is the new hotness for this? I remember a few years back there was an electric...

I got bored and made a dumb decision almost 3 years ago. I “needed” a truck for driving in the snow rather than my beater car or pavement princess. The best I could find was a pile of parts. I overpaid but I didn’t have time to drive out west to purchase other candidates. C’mon this was an...

My boy just bought a 1996 F-350 4x4 with the 7.3 powerstroke and ZF 5 speed transmission. Bought it fairly cheap because the output shaft of the transmission and input of the transfercase are wallered out and stripped. Would an output shaft and gear cluster from a 460 ZF 5 speed fit? Or even...

For those of you with a 90s F350 running 40x13.5x17s, what wheel backspacing do you use to keep the tires out of the springs? The internet ranges from 2" to 4.5" and I'm sure all of the info out there is correct. Curious what you found that works well.

Trying to work through some issues with the AOD in my 86 Mustang. Backstory for those of you not in chitchat: Pulled a 150000 mile drivetrain out of a donor 86 5.0/AOD cougar and put everything in my 86 V6 Mustang a few years back. Since then we built a fresh 5.0 with a few upgrades (GT40...

Hey just in case anyone is interested, and I’m sorry if this is not the right board, Speedmaster is having a huge sale today (Memorial Day only). Pretty much every item on their site is 35% off, and they have a ton of Ford 9” stuff. I’ve been scouting out pricing on 9” parts for the last week...