toyota

Girlfriends 2003 Tacoma is taking a shit, driving on the highway the throttle cuts out and goes into limp mode, throws a P2138 code. "The P2138 trouble code indicates that the Engine Control Module has detected a malfunction within the D and/or E circuits of the throttle position sensor." We...

2001 4 Runner just clicked off 300K and has started to run warm, I found a broken radiator cap initially and replaced it, This did not solve the problem. When I say warm I've driven this truck about 80K miles and it has never ran more than 205, and lives around 201 always. (Reading off the...

So I lost a HG on my crawler. Had the motor rebuilt by Davez offroad. Not many miles on it, mostly trail miles. Anyway some people are saying its a pain in the ass to do the repair with the motor in the truck vs puling the motor. Anybody got any advice?

Friend bought a sammy buggy with RA 8" front and rear. Rear has started puking fluid from both axle seals. I assumed it would use any off the shelf Toyota seal. Thought these on trail queers site would be the ticket. Date of manufacture on his housings is unknown. I mention that because of the...

I’ve been working on centering up my knuckles and setting the preload. I’ve been following the video series that low range off-road has on YouTube. In the video they say to put your scale into the hole farthest out on the arm when you use the scale. Well that’s all fine and dandy for the...

Can anyone that may have used the Toyota SST to center your knuckles share the numbers they got? I am following the FSM. I must be and idiot because by my calculations I need Negative shims It seems that the D dimension should be larger than the 3mm, otherwise you end up with a negative...

Has anyone dealt with toyota high steer arm taper actually failing when running hydro assist? My tie rod holes are an oval after about 5 runs. I'm running 555 tie rods, Marlin 6 stud arms, PSC hydro assist. Tie rod ends are torqued and pinned. Also is repairing the arms, welding and...

My dual-case 4Runner has often had a little clunk when when letting off the accelerator, but it has become very consistent when the rear case is in 4.70 low. (Cases are the typical 2.8/4.70 setup). I thought it was coming from the back but, after testing in the driveway, it appears to be coming...

Does anyone have a good carburetor for an LS1 buggy? 🙏🖕

I am currently going through the wiring for the 1998 2WD M/T 2RZ swap i am doing in my buggy. The first things that has me scratching my head is the wiring to the alternator. I have (3) wires coming from the plug. White, Red and Yellow & i have looked through lots of wiring diagrams but not...

After destroying a perfectly good 85 long bed I was forced to start over. My goal was to have a capable off road truck that had doors and a windshield. My previous truck turned into all tube off a toyota frame and was great while I was living in California and wheeling the Hammers. I moved back...

Should I paint these hubs to keep them from rusting or just leave them?

I'm currently putting together a decently built 2rz for my first gen 4runner with a supercharger. I have two diffren't harnesses and not sure which one is better. 1st complete harness is a 97 t100 which uses a distributor and the other full harness I have is from a 98 tacoma with the twin coil...

can anyone tell me the dimensions of the 22r/22re sticker on the valve cover?

Stepping to tons and gonna sell my yota axles. What is a built front (5.29s, OG longfield 30s, Longfield rings, 5th stud, arp hub studs, Yada Yada yada) worth now a days? Rear is stock IFS with 5.29s and link brackets. And another :flipoff2: for good measure

Picked up a 2008 reg cab 5-lug with a disassembled 2.7 (bad head gasket) for $2k with 277k miles. Decided to part out most of it, keeping the body, frame, and interior for a base build. I'm going to actually keep track of costs on this one in an attempt to keep the price relatively low. For...

Haven't seen any tech on this axle yet so thought I would start a thread, have done some searching and haven't come up with much all in one spot. Below is what I have found from searching on the internet the last few days, if anyone else has any details or corrections post it up. 2016+ Tacoma...

Not my show, but I will be there with the Prebummer

A lot of my build pics over the years have disappeared or were scattered over platforms/forums that do not exist anymore. So figured I would try and start over on a build thread. Everything started so pretty and simple. Was the 3rd owner of a 97 4runner V6 limited with beat up leather seats...

I can't figure why my damn fj80 axle is not venting properly. I have a vent line running from the stock location up to my gas door, and it still blows oil out the fill plug, and it has some suction when you go to pull the drain plug off. Evreything I have tried so far: No cap at the end of the...