jeep

So I have been looking for some steel corner armor for my 80 CJ5 but cannot seem to find anything aside from diamond plate (why do people like that?). I would really like to get some full armor down the side, but it seems those dont exist out there. To my knowledge the corner radius for the...

Located in Filer, Idaho. 2006 Jeep LJ. 4.0L I-6, 6sp manual, 3.8 Atlas II T-Case, aftermarket D44 front/D60 rear axles, 4.88:1 gears, chrome shafts, Detroit lockers. Front axle has manual hub conversion. 4" Currie suspension lift, 1' body and motor mount lift. Flat skid under T-Case. Currie...

So I had a separate thread on purchasing one and which direction to go, now it’s time for the build. Purchased a 2020 Gas, rubicon with 44,000 miles on it. Clearly has never been offroad. My plans are ud60 front, rear tbd, 5-6” lift, suspension, some body armor and 40”-42” tires. I’m...

Considering switching from ORI's to Fox coilvers. Main reason is the ORI's need adjusting with temperature changes. 2.5's or? Jeep weights about 3850 and running 37's. 9"R/D44F. What's a good starting point for springs? Walked by the Jeep this afternoon and saw this. Maybe a bit hard to...

Bought a TJ with a later model 4.3l V6. Runs great, no issues with power. It used to be a 4cyl model. Unfortunetly they mated it to a damn AX5. It also has Terra Low. (21 spline 231) and a Dana 44 rear. It has 4.88s and 33s now, Will run 35s next. I am looking into trans swaps before the AX5...

My good friend has a 97ish XJ, 4.0, auto, on tons. A couple months ago it developed this weird issue where it will idle like dog shit at temp. However, you can clear it by revving it to the moon for a few seconds, or kill it and start it again after letting it sit for about 5 minutes. It comes...

Hey guys looking into doing a drop tailgate conversion on my yj, but I'm curious about thoughts between the swag and the motobilt kits, thanks

I'm looking to see if anyone is running these on their truck and if they could grab a few dimensions for me. Specifically looking to see the installed height from eye to eye going down to the last leaf. I can't seem to find anyone running these on their trucks and RE hasn't emailed me back with...

This is the only forum I post on anymore, so I am going to start a thread for my CJ7 cruiser. If it is a boring build then move on, I use my threads as a memory bank of my jeeps so years later I have a document of something I did or bought. Instead of doing this on Jeep-forum or some other lame...

I am helping out on a pretty interesting EV project. Local guy is building an EV Converted Philippines Jeepney. He has a liquid cooled 50 hp motor from another conversion project that was parted out and asked me to do some of the machine work. The plan is to keep the T90 and adapt the DC motor...

I have 20 foot car trailer. I want to haul a KRX1000 and a XJ. Has anyone made a ramp system to raise one end of the SxS over the front of the Jeep or something similar? I don’t want a huge, heavy trailer because I am towing with a 2018 F150 or 08 E350 currently. I have airbags for the truck.

Was a member of the old "other" site. I have a thread on another forum that I am adding here. Sold my YJ, tons , stretch, sbc etc yada yada lol and found this! A 2004 khaki LJ. I always loved these when they first came out so this was a win. Recent rebuilt auto tranny, 4" RC lift, hard...

My current rig is a very well dialed 2007 jk. 1 tons, atlas, 40’s, etc. Unfortunately, it’s a manual and I’m over it and an auto swap isn’t happening. Broke my neck years ago and I’m now dealing with the consequences. The jk will cruise down the highway perfect (other than a significant power...

$50.00 Used. Good condition. Located in Durango, CO.

Currently running howell efi but I do not think the Howell does any fan control, unfortunately. Currently on the jeep there is a non-weatherproof mechanical temp sensor/probe that has seen better days. It was somehow wired in with 2 relays that would definitely not be enough for the high draw...

I'm considering doing something dumb and looking at switching gears from my 85 4runner and building a Commando. Anyone have one they could grab some measurements off of? Looking for a distance where the rear seat goes, for the widest inner dimension. Basically the inner tub excluding the wheel...

So I am working on my CJ (1980) with a AMC360 w/mild cam, Howell EFI, MSD 6A (AMC distributor), t176, 4:1 twin stick D300, D44 front and rear with chromos, etc etc etc. The jeep has the Howell EFI that works pretty well, but the vacuum advance has been disconnected. It runs rather hot though...

Is the VSS at the transfer case on a 1998 XJ required for drivability? My XJ is a buggy without a speedometer and I’m considering swapping in a 2007 NVG241 from a Rubicon. Is the Rubicon transfer case a good swap? Thanks

I did some horse trading for this project, spent a little bit of cash on it and now I need to dump it to turn it into cash for something else. Clean Kentucky title, Originally started off as a 95 jeep YJ, CJ front end conversion with flat fenders front and rear, and flat dash. 318 V8 with...

Trying to help a friend diagnose an issue. Its a 91 YJ with a 4.0 5spd. When cold it starts fine but at about 2000 rpm is starts misfiring and back firing. Once warmed up it runs fine. Driving while its warm is fine but if its cold outside and the engine temps drop below around 210 it starts to...