dodge

working on this 1990 ram charger project again. I'm having a hard time getting the alternator to charge. we gutted all the emmisions stuff and were using a holley sniper/ MSD 6AL. I was curious if any one had any insight on how I should have this thing wired up. I currently have the blue and...

So, over the weekend I finally swapped out my steering box and shaft on my 04 2500 with Borgeson "upgrades". Got the "dodge box" and shaft to accompany it. Figured while I was up in there, I'd just replace the pump and res with a stock replacement Cardone outfit. Flushed and bled the whole...

Looking for some 8 bolt 30 spline external hub drive flanges. If anyone has any they are tired of looking at or know of a place where I could buy some it would be much appreciated

Hi y’all. I’m going over my aging tow pig, and the leaking hydroboost is one of them. I’m able to source everything I need except…. These short PS hard lines at the hydroboost and the brake valve. My truck is 1997 Ram 2500. In my searching people can’t find them for their 3rd gen too...

Including: •Strong running 24V 5.9L with no blow by •NV4500 •D80 SRW Disc •D60 without the stupid CAD •Red sheet metal with a title •Transfer case with no front drive shaft ~185k miles $6500 CASH. No tades, not parting out. Engine is $3k+, a NV4500 'swap kit' are $3k+, being able to drive...

What is the recommended secret sauce now for these transmission?

Here is a Rock Crawler project that a buddy and I are doing. My part is to take the cab, Superduty axles and a pile of steel and make it a roller. To start we had to come up with a plan. 2x6 main chassis tubes, 1.75” DOM cage, Superduty Axles, 5.3 Motor, 3L80 trans, 241 case, front radius arm...

I’m working on stuffing an engine in a ram charger for a buddy and we ran into a snag with push rod length. The block is a typical LA360. The heads are from an old 340. We’re using the normal stamped rockers on the shaft that came on the older mopar stuff. We are on our 2nd set of rockers...

Posted to a couple Dodge specific forums with no luck so far: I'm thinking of swapping a 2009 SuperDuty Dana 60 into a 2002 Ram2500 4x4 with the 5.9L, NV5600, and Dana 80 rear. The easiest way to do the swap would be coilovers but to get an idea of what I need in terms of rates, I really need...

Probably not searching the right terms, but I have a 2002 Dodge RAM2500 with the Cummins, D60 front, D80 hybrid rear, NV5600. I am considering swapping in a Ford SD60 front axle out of a 2009 model I have lying around, mainly to get the better ball joints (I'll be doing a BJE kit for the upper...

Truck info: 2003 Ram 2500 CCSB 5-speed NV4500 trans NP 271 transfer case Previous Set up: AAM 9.25 w/ thuren truss and Synergy C gussets Synergy long arm kit Synergy Steering Synergy track bar 16" Fox 3.0 IBP coil over Cheapo daystar poly bumps New Set up: Ford Super Duty 60 w/ custom truss...

1994-2002 Dodge Ram 2500s with the V8 came with D60 rears apparently. I'd assume these are the 30 spline 1.31" diameter shafts and not the 35 spline 1.5" shafts most of us would want. So the question is: Is the spindle bore large enough to just swap in 1.5" shafts if you're already in there...

Will a dealer still do recall work on a "modified" truck.

I'm trying to find a decently cheap rear disc brake axle for my new project wider than the 14 bolts I have. I found that the 03+ Ram 2500 10.5 is 71-72" wms. Is the 2006 Dodge AAM 10.5 factory Anti-spin differential a clutch or gear type? Will it be usable with 39" tires in a offroad...

I'm trying to put 5.38s in a 2005 Dodge 2500 9.25 axle. My understanding is you need a spacer to run IFS GM front gears to get this ratio. No big deal. But I happen to have 4 or 5 9.25 IFS front diffs laying around. Can I just steal the carrier from one of those to avoid a spacer? If I buy a new...

So the jeep has suffered a dropped valve seat. I dig into the spare engine (blown HG) to steal that cyl head. Its distorted between the cyls to let a .0025" feeler gauge pass under it. Is this realistically going to seal with a new HG? Any HG's better than others? (Most are mls 3 layer steel)...

I currently have an NP231 DHD in my truck. I also have an NP231D that came with the speedo hole on the housing. I'm looking to swap the rear axle (not to the one I asked about a couple weeks ago), but the possible transplant axle does not have a speedo hole/plug where the current speedo plug is...

Basically have a bent housing and want to put all the guts in another good empty housing. Yes I know I could possibly straighten it out or build something out of a rear housing but I just need a bare GOOD condition front housing with carrier bearing caps. Located in the bay area, willing to...

Hey folks, I'm looking for a dodge 208 input shaft. 23 spline. Can anyone help? Thanks!

It's a 78 with a 440/727 auto. No rust except a little surface. Runs and drives great.