bronco

So I installed shoulder belts on the 67 Bronco today. Instructions said to mount the top 36" from the floorboards by drilling through both walls of the roll bar and running a bolt all the way through. Of course, this ended up being too high (the shoulder belt is at my neck). Ran across a forum...

For all things Bronco related... dumb questions, rude comments and etc. Just for Paul. :flipoff2:

Been meaning to do a thread but never got around to it. 1974 bronco that needs a total rebuild. I bought it 3 years ago and its pretty much the best of what's left when it comes to old Broncos. Not one tub piece is worth saving. The fenders, hood, grill and doors are in pretty good shape. so...

I have a 66 Bronco with Front and Rear Front 89 F350 axles. Using the stock Ford brakes with the dual piston calipers all the way around. Currently running an early Bronco vacuum booster setup. Any recommendations on what master cylinder to use?

So the time has come! Ive been avoiding Irate because I was too deep into other forums for way to many years but It looks like I had to make the switch. Features are looking promising and this place seems to be a good forum that adapted with modern times! With that said, I own and operate a...

Hi Everyone, A few weeks ago i purchased an 85 Bronco that my co-worker had sitting around. It has the 300 straight 6, 4 speed, 208 transfer case, dana 44 TTB front end and 8.8 rear end. Final drive ratio is 3.08. The A/C even works! Yes, it needs some work, it's not pretty but it runs...

Does the front gas tank from said F-150/250/350 use the same fittings as the same year ('94) Bronco? Meaning (aside from mounting); Take the front tank and, straight-across, plug it in with Bronco fittings. Unplug Bronco tank/take front tank with it's fuel etc and plug it in. I want a smaller...

I have an old aluminum finned deep c4 transmission pan made by B&M. I want to use it on a 76 Bronco. The inside of the pan has extra thick casting in the location where dipstick/fill tube would be located, so it seems to obviously be engineered to accept it with some drilling/threading/etc. Is...

I'm hearing that many of the Bronco places are hesitant on designing and putting money into new products as there is word of a platform change for 2023. Has anyone heard anything about it? I've done some searching and no one is really putting anything out for the new Bronco. It seems everything...

https://jalopnik.com/this-is-definitely-the-weirdest-bronco-project-on-craig-1847631960

Hesitation when starting started earlier this week; thought it was the POS starter acting up. This morning hesitated starting up, then when leaving the neighborhood, noticed hesitation when I attempted to accelerate. Also notice once the RPMs were up it appear to work fine; although I never...

Here is a little info on my truck as it sat before the swap: 1981 custom package w/ rear sliding windows, GT rollbar, front bench seat and factory tachometer T19 transmission swap. 5:1 first with synchro'd 1st and 2nd (unlike 'granny' T18 and NP435) Mildly build 4.9 300 straight six (Holley...

In these times of crazy used car prices, I think now is the time to help my parents unload some of their stuff. My mom has this Bronco that she bought barely used. Due to some health problems she no longer drives it, and before my younger brother wears it out I think she should cash out. It's a...

Tuesday question on a Thursday. :flipoff2: What degree bushings should I go with for a 2.5" lift? Both 4 and 7 degree bushings are listed. I'm never going to lift it more than 2.5" and I just want to run 31x10.50x15's.

It started and ran and sounded decent for 45 seconds, I was about to shut it off, add coolant, triple check everything anyways... So after doing all that, it just cranks, I was running out of time, I didn't actually do a spark test, but now I'm thinking it's flooded Timing, at this point, was...

This is my brother’s 1992 Bronco. It’s an Eddie Bauer, it was given to me in 2006, then given to my brother for his first car. We have historically used it as a daily, camping rig, tow rig, and now trail rig. We wheeled it on TTB with some leftover 35s, welded the 8.8. Had a blast and beat the...

Well I finally made the move from Pirate. Owned my 66 bronco for over 11 years and have decided to rebuild it again. https://www.pirate4x4.com/threads/early-bronco-dilemma.1067075/page-11 Been plugging away at frame and suspension. Got the atlas mounted. Had to cut up the axle to rotate the...

Ever since attending my first King of the Hammers in 2016 I have had a hankering to race in the in the 4600 Stock Class during the Every Man Challenge. After the initial enthusiasm and planning out the costs to put together a reasonable race effort, I had resigned myself to racing being too...

So my 351m said enough is enough of the milkshake oil multiple times or the holding the rpms in the red zone far to long at tittie lane at redneck yacht club and it is now knocking. I thought it loved it but i guess not..:homer: IMG_20200118_140244 by Angelo Mehtala, on Flickr vidya of the...

Another forum to keep up with, I guess :D So, back story. My pops bought this 1968 Bronco from Bob Lewis of Lewis Off Road enterprises back in 1972. He drove it for a while, and blew the engine in '78. It's been in a garage ever since. Yes, this truck has not been running longer than I've...