What's new
By:
Filters

struggle bus munting my DE ram in TMR mount.

I've always ran all four ram clamps and have offset the ram due to diff covers. not to say there is or isn't a difference, but I've never been able to notice it.

Currently I'm re-fitting an existing Trail Gear 609 that was built with the center section closer to the middle into my 4800 car. even without a diff cover to contend with I'm going to have to offset the ram much further than I have previously to fit all four clamps. Are three clamps enough for racing in the woods?
 

Attachments

  • 20240220_114801.jpg
    20240220_114801.jpg
    3.7 MB · Views: 45
Might look into the Hulse Engineering mounts for a fabbed housing. They only require two b/c the ends are captured and are designed to be able to french on into the diff side.

hulseengineering.com

3" Slammed Steering Ram Clamps

These fit the PSC 3x9" and 3x11" double ended hydraulic steering rams only (SC2217 or SC2228), they do not fit 2.5" or 2.75" rams. Billet aluminum top cap and steel lower. They allow you to drop the ram almost 1” lower than the PSC clamps and weld the base directly to your ram mount/skid. They...
hulseengineering.com
 
cdemart2 said:
I've always ran all four ram clamps and have offset the ram due to diff covers. not to say there is or isn't a difference, but I've never been able to notice it.

Currently I'm re-fitting an existing Trail Gear 609 that was built with the center section closer to the middle into my 4800 car. even without a diff cover to contend with I'm going to have to offset the ram much further than I have previously to fit all four clamps. Are three clamps enough for racing in the woods?
Click to expand...
I've clipped a tree at 40mph with3 clamps and broke both high steer arms.
The three clamps are fine, not even loose.
 
Bebop said:
I've clipped a tree at 40mph with3 clamps and broke both high steer arms.
The three clamps are fine, not even loose.
Click to expand...

yeah clipping trees at speed is my issue

thanks guys I guess I'll leave one off.
 
Sean said:
Might look into the Hulse Engineering mounts for a fabbed housing. They only require two b/c the ends are captured and are designed to be able to french on into the diff side.

hulseengineering.com

3" Slammed Steering Ram Clamps

These fit the PSC 3x9" and 3x11" double ended hydraulic steering rams only (SC2217 or SC2228), they do not fit 2.5" or 2.75" rams. Billet aluminum top cap and steel lower. They allow you to drop the ram almost 1” lower than the PSC clamps and weld the base directly to your ram mount/skid. They...
hulseengineering.com
Click to expand...

I've seen those, very bad ass! I have an older psc ram they called xrc that came in the race kits. they no longer produce that ram or the race kits, I don't think I've seen a low profile mount like that for my ram.
 
cdemart2 said:
I've seen those, very bad ass! I have an older psc ram they called xrc that came in the race kits. they no longer produce that ram or the race kits, I don't think I've seen a low profile mount like that for my ram.
Click to expand...
That's what I have too.
Slawson had them make another run and still has some in stock if you need a spare.
 
cdemart2 said:
I've seen those, very bad ass! I have an older psc ram they called xrc that came in the race kits. they no longer produce that ram or the race kits, I don't think I've seen a low profile mount like that for my ram.
Click to expand...
I bought a set for one of our portal cars.....they are very nice but obviously there's a weight penalty. I wonder how much lighter the JHF version is. Looks to be substantial.
 
Bebop said:
That's what I have too.
Slawson had them make another run and still has some in stock if you need a spare.
Click to expand...


thanks for the heads up. I know I saw them somewhere. not sure if I have room for any clamp on the end of the ram unfortunately. I may fab up some tabs to go up against the ram body just for added security.
 
You must log in or register to reply here.
Top Back Refresh