swap

I looked through the search and couldn’t find anything. I’m new to it all but my dad is knowledgeable and can help me do all the work. I currently have a 2wd 99 4runner with a 3.4. I have a chance to get a wrecked 96 4x4 and want to swap in the front end 4x4 parts and the trans and transfer...

searched the internets with not much luck. I recently carb swapped my TBI 454 in my 1990 3500. i did the comp 4x4 cam, a set of 502 heads, eldebrock alum intake, long tube headers and topped it with a holley street avenger 770. the issue is it will only shift at like 3500rpm or higher. the...

Not a lot online. My pops keeps having the blues with the anemic 1.3. we did a turbo install, had a professional shop tune it, it only lasted a few hundred miles. New engine with a hot cam keeps having carb issues due to ethanol. And only 100hp. I have a Corolla with the 1ZZ-FE 4 cylinder...

Looking at doing a WJ knuckle swap on my TJ. I'm already running 5 on 5 adapters. Can I just use the WJ 5 on 5 hub instead of an XJ 5 on 4.5? Would I still need the .25" spacer ?

i have 3 OBS Suburbans (2) K1500 and 1 K2500. the 2500 is a 99 with 454 , 4l80e and a full float 14 bolt with disc brake conversion and hydroboost . i have a 96 with blown engine but a 6 inch RCX lift, and lots of new parts and a 93 with a good body. ive already scrapped the body of the 99...

These were my dads, they aren't in great cosmetic shape but I ran them both a few years ago and they ran fine. I'd like to swap for baitcasters and or flyrods. Located in napa 94558

I have a low mile (around 10k when pulled) 5.3 L83 Gen V/LT motor ready to go. I had it in my YJ running and driving hooked to to a TH-400/205, got a deal on 6.2 so I swapped them. This one is complete with standalone harness, standalone tuned ECM, Truck gas pedal, etc. have Videos of it running...

I feel ******ed even asking this. I have a 99 taco v6 cab going on a 97 taco 2.7 frame. Do I gotta swap the complete dash and wiring, or is there a quick way to swap the gauge cluster and ECU and use the rest of the v6 wiring? It just seems like a lot of work :lmao: I know the engine harness...

Picked up a nicely painted CJ with a v8 swap and no suspension or axles. Ready to get this thing driving now and tidying up some wiring and finishing touches. The kick down cable has no bracket and there is an unplugged sensor with no connecting wires I can see. It does start but I want to get...

So since I am Dumb (maybe even Stupid because I already have a 2004 Majestic 23p Class C) I decided to buy a slightly clapped out 1996 Scotty 25 ft Class C (on a 1995 Dodge 3500 cab and chassis with 84" CA with a V10 in 2wd), that took a 6 hrs drive to go see it and a mountain of paperwork at...

I'm posting this here for a friend of mine, she's not a member. I'm also doing this to ask ya'll, if no one here wants it, how much $ to charge the rest of the world. The rundown: 1993 4runner 5 speed 4wd -1997 3.4 swap -stock 5 speed and drivetrain -245/70r17 (new September '23) on 5th gen...

Looking at swapping in some full sized axles out of a Wagoneer. I have found the Motobuilt kit as well as Dave’s custom unlimited kit. Curious if anyone has experience with either or have another that they like. Major difference is Motobuilt has shackle reversal and Dave’s does not. This is...

So I've looked into this for a bit and can't find any information regarding it other than it wouldn't work due to the size differences, figured I'd give it a try and document it for anyone who might want to try it. I mean, what's the worse that can happen? So initially my goal was to do this...

Most of my toyotas are still RE's, and I know most people upgrade them to 2.7's or 3.4's. My 02 Taco has the 3.4 with about 225k on it. It isn't a power house by any means, and at some point in the future, its going to need to be replaced or rebuilt. Its not that I "Need" to replace it with...

Doing an LS swap in an LJ for a buddy and have the engine set in the frame and need some feedback before I burn it in. I currently have the engine 3/4" to the passenger side. I've done this on previous builds and it works well with a drivers drop front axle. I currently have a flat skid with...

95 Bronco E4OD, was running great in December 2023, and that’s when I started my one ton axle swap. I installed a Sterling 10.5 out of a 2000 f250 or excursion with VSS w/ringtone. I just got this running about a month ago and I got some problems now. -Flashing O/D off light -blank odometer...

I have two trucks that we just swapped to rear discs since it was cheaper than rebuilding the drums. One is my sons 1986 K20 and the other is my 87 K30. Both trucks have the rear discs dragging just a bit making a "womp womp" noise while rolling. I am still running the original brake system...

I'm hoping to get some input or ideas on a wheel speed sensor problem I'm having. I'm at the tail end of a build out and I am stuck trying to figure out why I can't get my speedo working. Normally I wouldn't care and I'd just reference speed on my gps but the WJ needs the wheel speed sensor data...

So I have long tube 454 headers on the Burb which have been ****. The taller deck height on the 8.1 pushes them right against my shackles. They hang down pretty far. I'm ready to make this right. Not a 100% sold on headers and would be happy with manifolds. Manifolds run a little over a hundred...

This truck is getting tore down around October this year, will going back together with a 98 P pump 12 valve , 47rh transmission, dodge Np205 , chevy dana 60 front, and 14 bolt rear axle. The truck is currently a driver with a 350 / 700r4. I am currently working on building up the 12 valve...