Last Call Guest on these Group Buy Deal Items from Baja Designs

gt1guy

Apparently a racist From New Iberia, La.

Joined: May 19, 2020

Latest activity Postings Media Post Areas About Events

- gt1guy reacted to Rustyfabshack's post in the thread Build Family Size Rat crawler with Like.
  
  csutton7 I like how yours are recessed. I used a leather strap for the outside handle because it is easily replaceable, flexible and...
  
  Today at 3:29 AM
- gt1guy reacted to Malburg114's post in the thread Build Tacoma 4500 build with Like.
  
  Rear boxes are done. Just waiting for paint to dry. I need to make some knobs to help open them. Mounts are also done.
  
  Today at 3:15 AM
- gt1guy reacted to achase6002's post in the thread The bat ..ls 40s and tons TJ to LJ with Like.
  
  Yikes ..not our best work. Good news we are getting better as we go. Ill have to grin that down and get some more pentatration
  
  Yesterday at 5:22 PM
- gt1guy reacted to achase6002's post in the thread The bat ..ls 40s and tons TJ to LJ with Like.
  
  Drop down tailgate done
  
  Yesterday at 5:22 PM
- gt1guy reacted to TrikeKid's post in the thread Build "Tweety" the '45 MB with Like.
  
  So, haven't done **** to this thing lately but I did need to drag some logs out of the woods and this was the right tool for the job...
  
  Yesterday at 5:12 PM
- gt1guy reacted to D_JEEPER's post in the thread Build Project Iron III Oxide: A Snowball Effect with Like.
  
  Took a few minutes to make some labels for the switches :grinpimp:
  
  Yesterday at 5:11 PM
- gt1guy reacted to D_JEEPER's post in the thread Build Project Iron III Oxide: A Snowball Effect with Like.
  
  Woo, finally got this stupid OD switch mystery solved :emb: So yeah, OD switch wire touches ground to signal OD OFF, and the OD lamp...
  
  Yesterday at 5:11 PM
- gt1guy reacted to D_JEEPER's post in the thread Build Project Iron III Oxide: A Snowball Effect with Like.
  
  OK, got off the phone with Chris at Hotwire Auto. Turns out with the OD Off switch, the Orange OD Switch wire gets toggled to ground...
  
  Yesterday at 5:11 PM
- gt1guy reacted to Fastspec2's post in the thread Stuff I'm working on. with Like.
  
  Apon tear down. Actually got a bit further but will post those pictures tomorrow. Motor out and ready to tear down on the stand. Pan...
  
  Yesterday at 4:53 PM
- gt1guy reacted to HYDRODYNAMIC's post in the thread Dust Buggy with Like.
  
  The big bell axle assembly will pass through the knuckle. RCV made the big bell just smaller than the unit bearing. The stock knuckle...
  
  Monday at 5:19 PM
- gt1guy reacted to HYDRODYNAMIC's post in the thread Dust Buggy with Like.
  
  Wheel check with super high steer. Wheels are 17” x 8.5” x 4.5” backspacing The high steer spacers are aluminum so while it looks like...
  
  Sunday at 4:44 AM
- gt1guy replied to the thread Post a picture of where you are right now..
  
  All this should take a while to install. 3 - 12" risers 3- 12" J-Tubes 17- 12" spools Riser clamps Big yellow thing is the...
  
  Friday at 7:48 AM
- gt1guy reacted to Mad Max's post in the thread 14 JKU M-380 "Kilroy" with Like.
  
  so I've got two big trips coming up, and to get ready for those I've been working on both the tow rig and the Jeep. On the tow rig, I...
  
  Friday at 4:34 AM
- gt1guy reacted to D_JEEPER's post in the thread Build Project Iron III Oxide: A Snowball Effect with Like.
  
  Got the radiator fan controller lines ran and power lines loomed back to the battery. Still need to crimp and do some zip tie action but...
  
  Friday at 4:32 AM
- gt1guy reacted to D_JEEPER's post in the thread Build Project Iron III Oxide: A Snowball Effect with Like.
  
  Once again in parts limbo. Got my switches in for the Proform Fan Controller bypass so I installed that. Then I got the union for the...
  
  Friday at 4:29 AM
Show older items
Loading…
Loading…
Loading…
Loading…
Loading…