locker

Have a torq locker for a 14 bolt. It is brand new in the box, opened it up and decided to just weld it since my rear diff had a gov-lock. They go for around $290 new so $250 for this one and it is yours. Located in orange county/La area.

Seems too good to be true? Buy 2 for $760? https://www.ebay.com/itm/395476925602?itmmeta=01J8Z689YSZ8XBNH83H6BSAASY&hash=item5c1442fca2:g:T~UAAOSwYB9mcMjD I thought these were Chinese ARB knock offs for a while, but turns out they've been around for years in Australia and are just making it...

Looking for limited slip / locker for a standard rotation dana 60 - 30 spline - 4.10 & down - automatic.

Location-central indiana Looking for a selectable super duty 60 locker, 35 spline 4.10 and down. Partial to Eaton e-lockers...may consider an ox.

Am I going to have an issue using track/ring and pinion gears with a Samurai air locker in a samurai third? I know I’ve done it in the past with lunchbox lockers and the pin cans. I’m mainly wondering if I’ll need the pin can and side adjuster spacer with a full case air locker or if they...

Is there anyway to adapt a Toyota 4 cyl. Grizzly locker to an FJ80 high pinion 3rd member? I called East Coast Gear Supply and they said they don’t work. But I found something on the old place that briefly stated running something from Davezoffroad, but it’s a dead link. I’m not familiar...

Anyone have any leads on older detroit locker part number. I have a 56588 locker laying around that was given to me. Trying to figure out what it is. It's 35 spline I know forsure.

JFYI: Vehicle is '99 4Runner 3.4L, 5 spd, D70U (or D60 rear), 5.86 gears, 40s. Rear axle application (front axle is a KP60 with hubs). Only reason I've ditched the 14B rear is for the gear ratio that I need. Has anyone run both of these lockers on the street that can compare? Torq's site...

Got a few leftover parts from past projects. Everything new in Box: Nitro 5.29 gear front - T8S-529R-NG - $300 Nitro 5.29 gear rear 8.4 - T100-529-NG - $200 Nitro install kit (don't have box but it's all there new) - MKT100 - $250 Solid pinion spacer w/ shims - SKCST100 - $40 Detroit Locker®...

Looking for a full case locker for a Toyota IFS 7.5" ideally prefer a ARB, but would settle on a Detroit or LSD. Just trying to get away from the stock carrier.

New, never used, but has been sitting around for a few years so it does have some harmless surface rust on it. 16-spline. Bought for a project that never got off the ground. Will ship on buyer's dime, located in Gulf Breeze, FL. $350

Vendor had it labeled wrong and was trying to use in a Jana 76 kit with a thick cut currier super 70 gear. Ground the back side for clearance. New never ran just setup multiple times.Come with air collar,air line etc. Located in Villa Ridge MO Will ship for asking price

Looking for a 31 spline Detroit locker. Mine broke when I snapped an axle shaft last trip out.

SOLD! Bought this to go in a TruHi9 third. Been on my shelf for probably 5yrs. Just now cut the outside box open to see the part number:laughing: 35 spline. Located in Central Missouri. $800 shipped.

Is this a stock limited slip or something else?

Anyone use one of these for chainsaw chains? Feedback? Comments? https://chainlockerusa.com/products/

Since were new here figured we let folks know some of the parts we offer. For the Ford Super Duty axles we have a few components that may interest you 99-04 High steer Arms 7075 https://dffabrication.com/store/ols/products/superduty-high-steer-arms-99-04 05+ High steer Arms 7075...