axle

I have a tandem axle flat deck. I need a bit of weight off the front, but the overall weight is way under capacity. It has 3 leaf spring packs all around with the standard equalizer setup. Thinking of putting some 5 leaf spring packs on just the front axle, hoping that it takes more of the...

Gbkeith was nice enough to scoop up a ford d60 and matching rear local to him, midland area. Still getting specs on the rear, if it's nothing special I may just have the front hauled to make it easy on everybody. He has a crane and I have a forklift.

Bolt on plate to adapt 2021-2023 F150 rear brake calipers with integrated electric parking brake to Sterling Super Duty axle. Cut flat plate from .25 minimum. Inside standoff is 1in OD 5/8 ID and .750 length. Outside caliper standoff is optional. Sand brake pads down to .630 total height to fit...

SOLD 5-20-25 Rear Axle: Currie 60 Rock Jock 3 – 4.56 Gears – ARB Locker – Disc Brakes – 35 Sp. Shafts Front Axle: Currie Dana 44 – 4.56 Gears – ARB Locker – WJ Knuckles - WJ 2 piston Calipers – CJ Rotors – Alloy Shafts with 30 Sp. Outers - Warn 5.5 HD Hubs with Locking Hub kit Both axles are...

I figured this would be a good place to ask. one of my best friends just picked up a 97 F250 from Grand Junction CO and it came with a set of 99-03 axles. we plan to do the swap towards the end of summer. Are there any specific details I should be prepared for? I know there is a ton of info out...

Had some potential on pbb. Might be helpful to some since a lot of axles have stigmas for hanging way down when they really don't. This is center of axle to bottom of diff measurements. Sami 4.25" Toyota 8": 5.125" Stock 8" Toyota, minus drain plug 5" Shaved 8" Toyota 4.25" LC 9.5": 5.625"...

I've been trying to gather information on these axles for a while now and I've found a decent amount, but not a single great resource for tech on these axles plus a lot of misinformation thanks to Jeep/Dana advertising these as D44's. I've got a few of these axles laying around now and am...

Howdy Yall, I’m in the beginning stages of building a front D44 to sling under the front of my 3rd gen 4Runner. Axle prices are stupid these days but my labor is cheap :flipoff2: I picked up a 70’s chevy d44 for a song with the intention of retubing it to drivers drop. Its got 4.10s in it which...

I bought these few years ago from ECGS and never finished the axle. I have the Crane Adjusters, and the inner axle shafts 1480 style. I was going to use GM Dana 60 king pins outers so the shaft length is similar to if you wanted a GM D60 width with 14B center. Both inner shafts and the adjusters...

I think the kids have outgrown the 24s, no amount of mods makes them fun to crawl with my 1/10th scale. My middle kid is the most interested and will still try to play follow the leader. So I decided to get the 1/10th version of his deadbolt and build something that should be fun to crawl with...

Like it says on the tin, It seems that the aftermarket doesn't have a direct factory style replacment. If you have a bad rzeppa joint (CV) in one of the front axle shafts, would you: replace with another from MOPAR replace with aftermarket with proper u-joints why? Assume its going to stay...

Looking for some info from those who know. My brother in law bought an '89 GMC 1 ton for a wooden cutting and plow truck. It has an open diff and I told him I'd put a locker in it for him. I looked under it expecting a 14 bolt and it has a Dana 70. It's an IFS single cab longbed with a 454 and...

hay folks! im building a 64 F600 bass turd. im looking for a steering arm that will convert the 08 F550 front axle from cross over steering to lateral. the chassis im using is a 97 F700 chassis. converting this chassis, to lateral steering is a complete beach. and i want to do it a little...

I had a conversation with my chassis builder he was against my idea of using lower transfercase gearing. He said lower axle gears make the chassis steer better with less stress on the chassis. I’m assuming torque steer or something of that nature. What are y’all’s thoughts? I’m a big fan of a...

Mostly factory Dana axle shaft specs

New year, new me or at least new thoughts on my 2002 Tacoma:flipoff2: Short: What non-full width front axle is good idea for 2002 Tacoma getting leaf sprung SAS to fit 35-37" tires for rock crawling? Goal is 60-64" WMS axle and 4-5" of lift total. Currently bench building with eye on...

Anyone know what the heck this is? The smooth center section is throwing me for a loop. Not a 9" with no bolt in bearing. Saw it on a Facebook page stuffed in a YJ.

Built a couple of these Axle carts before a move a few years back to hold my super duty axles and make them easier to move around/store etc. Nothing fancy but axles roll around nicely on the casters, 2 locking, 2 non-locking. Has a built in shelf for organizing smaller pieces if you have the...

This is an edited file that allows for 3 clocking positions each 20 degrees apart.

Anyone know what this is? A buddy sent me that picture. He thought it was newer jeep but those are 5 lug.