-
Last Call Guest on these Group Buy Deal Items from Baja Designs
Carnage share thread
- Thread starter JR4X
- Start date
Beat95yj
Rolling 24/7
The funny part is I live halfway up that first map, which means it’s only about 5 miles from here. 😂
If your that close to a DG, you can't be in a good nieghborhood.
Beat95yj
Rolling 24/7
😢. Does it help that that’s probably an hour drive? At least I’m on the good side of the 405 which that is not.
There are no good sides of the 405 above south OC.
Beat95yj
Rolling 24/7
I am nowhere near the OC. That store is probably in Inglewood. Which has nice areas, but they are few.
Last edited:
Lies, you've got Stockholm syndrome from being stuck in HelLa for too long.
Beat95yj
Rolling 24/7
Lol I live in Mayberry. A bunch of retirees that walk their dogs all day. If they weren’t all liberal, it would be perfect.
I’ve lived plenty of worse places in California.
The worst part about it is we have big lots and idiot. Newsom made it too easy to build auxiliary housing units in the backyard. Every house that sells get sold to a in an ADU. Which just decreases parking on my street but I could still park my old 34 foot RV in front of my house without much trouble even with the 20 foot trailer. That’s rare in LA.
I’ve lived plenty of worse places in California.
The worst part about it is we have big lots and idiot. Newsom made it too easy to build auxiliary housing units in the backyard. Every house that sells get sold to a in an ADU. Which just decreases parking on my street but I could still park my old 34 foot RV in front of my house without much trouble even with the 20 foot trailer. That’s rare in LA.
dnsfailure
WHAT GEAR ARE YOU IN?
Yep, even where I'm at, some houses I swear have like 2-3 families living in them and 5-6 cars on the street. I have a lot of vehicles, but I park most of them in my yard and behind the house and only leave 1 or 2 on the street (no driveway)
- Thread starter
- #1,120
I live a few blocks from one. But I live in Farmington NM. Already know without a doubt I can’t be in a good neighborhood 🤣
You could have stopped at NM.....
redneckK20s
Well-known member
There are 3 within 10 minutes of me. My house cost less than most new pickups. You're not entirely wrong.
Tech Tim
Your AD Here....
CarterKraft
Thread ****ter Upper
2009 Yamaha 250 HDPI SII driveshaft bearings.
These are supposed the Torrington roller and needle bearings.
These are supposed the Torrington roller and needle bearings.
redneckK20s
Well-known member
2.6K views · 65K reactions | How to disconnect the Rotating assembly from the Engine Block… #Nova #chevy #motor #enginefailure #friday #fridayvibes #localart | TripFrom DaSipp
How to disconnect the Rotating assembly from the Engine Block… #Nova #chevy #motor #enginefailure #friday #fridayvibes #localart
www.facebook.com
TTRAxle&FAB
Yellow Skull
- Joined
- Mar 15, 2023
- Messages
- 236
Cross pin said "I'm out". Pulled the shafts and hubs. And sent it too the scrap yard
Winchested
IH Scout SSII
Details on said 14 bolt? Gov lock?Cross pin said "I'm out". Pulled the shafts and hubs. And sent it too the scrap yard
TTRAxle&FAB
Yellow Skull
- Joined
- Mar 15, 2023
- Messages
- 236
Open diff. Was in a square body pickup. Guy said said he was in reverse and slammed it into drive. Didn't make it very far. Before one of the pins grooved the carrier and exited the housing.
CarterKraft
Thread ****ter Upper
A friend of my son.
gt1guy
Apparently a racist
- Thread starter
- #1,134
How? That is a horror story
GLTHFJ60
Stupid is as stupid does
Burn it to the ground and file an insurance claim, lolA friend of my son.
YotaAtieToo
Thick skull
You see the Crack going all the way back?
You think it's easier to weld that up and find carrier and set up gears and everything than just bolting another axle under it? Assuming stock axle under a stock truck...
Levigarrett76
Glass Half Empty
thats a bad time
D_JEEPER
Picked the wrong week to quit sniffing glue
- Joined
- May 21, 2020
- Messages
- 1,295
A friend of my son.
lt1yj
Well-known member
- Joined
- Jul 6, 2020
- Messages
- 297
I had almost the same on my GMT400 when the front driveshaft let go. Luckily I parted out a similar truck and saved the engine and transmission harness. Four hour swap. I can’t imagine trying to fix a harness like thatA friend of my son.
Mr. Mindless
Well-known member
I had intermittent running and dash issues on a relatively built XJ on 35s leaving Sand Hollow. I'd lose the whole dash once in a while. Sometimes the dash would go nuts and I'd have a partial engine stall.
I'd bought it in Colorado Springs, drove it to Sand Hollow and wheeled it hard for a week, and this was just getting onto the highway leaving.
It got bad enough and frequent enough that I hoped I could findsomething that I could do something with, and I found an underbody harness just barely rubbing on the front driveshaft and had worn through insulation on a couple wires. Never caught and ripped it out like that. I taped it up and drove 2000 miles home.
I like my near miss a LOT better than that. Nightmare ****.
I have probably shared it here before, and I don't have pictures, but a local volunteer fire department bought a new brush truck about 15 or 20 years ago now, and the upfitter zip tied all the front lighting wiring to the driveshaft. modern-ish truck with a front axle disconnect. First time they put it in 4x4 it went back in for a lot of service.
I'd bought it in Colorado Springs, drove it to Sand Hollow and wheeled it hard for a week, and this was just getting onto the highway leaving.
It got bad enough and frequent enough that I hoped I could find
I like my near miss a LOT better than that. Nightmare ****.
I have probably shared it here before, and I don't have pictures, but a local volunteer fire department bought a new brush truck about 15 or 20 years ago now, and the upfitter zip tied all the front lighting wiring to the driveshaft. modern-ish truck with a front axle disconnect. First time they put it in 4x4 it went back in for a lot of service.
