Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
Official Part Weight Thread
- Thread starter '84 Bronco II
- Start date
Sterlingfire
ignant
You can edit your first 4 posts to include all the data
YeeP
Red Skull Member
Ok. I was just going to say let me know if you want me to copy paste something and put it there so it is in the same position
'84 Bronco II
El Chingón
Sorry, I am slow, I get what you're saying now. I'll wait and see if Austin can provide a more elegant solution.
YeeP
Red Skull Member
Honestly, I'll post whatever you want in there. I don't care. Just tag me when you want me to do something out of my phone set up so it notifies me. Sorry if I messed up your thread, I was just excited to see it
Sterlingfire
ignant
That's a good idea too. I just figured 84 already had about 5 posts right at the beginning of this thread, and if you and Chaplin and even i delete our first couple posts he can have all of his first posts right at the top to edit. We'll see what Austin comes up with.
YeeP
Red Skull Member
Sounds good. I'll hold when I'm at right now until you guys figure it out
Sterlingfire
ignant
I don't think it is messed up, and i doubt 84 does either. Together we can make it work
Sterlingfire
ignant
Nah you're not slow, I'm just lucky with decent ideas right now
Sterlingfire
ignant
Honestly post #12 is the first with any relevant data(beside 84's, if those of us above that were to need to delete to give 84 more room, i think that would give him the first 6 or 7 spots to post the actual data. He could just take mine and Chaplin's pics of our crane scale and edit it into one of his posts.
YeeP
Red Skull Member
Or start a new thread. Grab like the first ten posts right away
Sterlingfire
ignant
Yeah but everyone who already posted pics with weights will have to repost...i assume Austin will have a way to do this the easiest way possible...
chaplinfj60
Well-known member
Just let me know what I can do to help
chaplinfj60
Well-known member
I deleted my first post here.
Also.
Aluminum 33 lb Forklift tank full of propane.
53.8 pounds.
I carried two of these. Some times steel some time aluminum. I dont have a full steel tank so i cant get a Comparison.
And gasoline weight is 6.1 pounds per gallon approx. if i goto a 18 gallon fuel cell from goat built that will be 110 pounds in just gasoline. Basically its a wash in the weight by changing fuel systems.
Also.
Aluminum 33 lb Forklift tank full of propane.
53.8 pounds.
I carried two of these. Some times steel some time aluminum. I dont have a full steel tank so i cant get a Comparison.
And gasoline weight is 6.1 pounds per gallon approx. if i goto a 18 gallon fuel cell from goat built that will be 110 pounds in just gasoline. Basically its a wash in the weight by changing fuel systems.
Sterlingfire
ignant
Once this is all straightened out in going to delete all of my non- relevant posts. Especially those just above
YeeP
Red Skull Member
Same here.
chaplinfj60
Well-known member
205 Chevy with ORDs 32 spline rear output, front 30 spline factory, with magnum from ORD, no yokes 166..
forgot to get a tape measurement.
forgot to get a tape measurement.
gt1guy
Apparently a racist
Hero 3spd. Has the vss on the output.
150lbs
150lbs
'84 Bronco II
El Chingón
Hero 3spd. Has the vss on the output.
150lbs
Damn, that's a lot heavier than the two speed!
I need to get off my ass and update the OP.
RunningProblem
Red Skull Member
- Joined
- Sep 12, 2020
- Member Number
- 2860
- Messages
- 2,733
You could put together a list of parts, their weights, and a direct link to the post with the photo. The direct link button is in the header of each post.
Aluminum propane tank | 53.8 lbs |
Official Part Weight Thread
Hero 3 speed | 150 lbs |
Official Part Weight Thread
'84 Bronco II
El Chingón
I already have that setup if you click the "source" link in the listings on my first few posts in the thread.
RunningProblem
Red Skull Member
- Joined
- Sep 12, 2020
- Member Number
- 2860
- Messages
- 2,733
I didn’t see that. 
RunningProblem
Red Skull Member
- Joined
- Sep 12, 2020
- Member Number
- 2860
- Messages
- 2,733
Dana 60 (kingpin) outer axle shaft
6 pounds 15 1/2 ounces
6 pounds 15 1/2 ounces
RunningProblem
Red Skull Member
- Joined
- Sep 12, 2020
- Member Number
- 2860
- Messages
- 2,733
Dodge Durango steering box
27 pounds 2 1/2 ounces
27 pounds 2 1/2 ounces
RunningProblem
Red Skull Member
- Joined
- Sep 12, 2020
- Member Number
- 2860
- Messages
- 2,733
NP242 23 spline input planetary
9 pounds 12 1/2 ounces
9 pounds 12 1/2 ounces
RunningProblem
Red Skull Member
- Joined
- Sep 12, 2020
- Member Number
- 2860
- Messages
- 2,733
Ruffstuff front frame stiffener (half) plates
6 pounds 14 1/2 ounces.
6 pounds 14 1/2 ounces.
gt1guy
Apparently a racist
LS3 6.2L.....no front drive accessories, coolant, or oil.
6l90e......no torque converter or oil.
Hero 3spd TC.
Billet tc adapter, trans mount and tc mount are there too.
721lbs.
6l90e......no torque converter or oil.
Hero 3spd TC.
Billet tc adapter, trans mount and tc mount are there too.
721lbs.
chaplinfj60
Well-known member
Wow. That’s light. I think my 5.3 is 500 plus. And tcase is 166. No tranny.
gt1guy
Apparently a racist
What I found interesting is that there's a scale under the engine oil pan and one under the trans pan. The engine oil pan scale is reading 271lbs and the trans pan is reading 450lbs. I totally expected it to be the other way around. That tells me the the trans mount will always see way more weight than the engine mounts. I would have never guessed that was the case.
I have to break everything apart here soon, so I'll be able to get individual weights of the engine and trans.
chaplinfj60
Well-known member
That is. I did not see that. Very cool