22r "tick" at low rpm

Collapse
X
Collapse
First Prev Next Last
 
  • Filter
  • Time
  • Show
Clear All
new posts

    22r "tick" at low rpm

    TLDR version
    83 22r 15 year old jasper reman with less than 30k. Has a tick at low rpms that seems to fade out as rpm rises. I am 90% sure it's timing chain related but what else should I check before I pull the motor.

    What I have already checked.
    compression test in spec and even across cylinders
    valves adjusted
    timing chain guides visually inspected from above and below and look good
    oil pump replaced
    rod and main bearings checked and plastigaged and in spec
    all accessories water and fuel pump eliminated
    Put a stethoscope on it and it seems like it's coming from the front of the motor but the noise is definitely carrying through the engine

    Long version
    After a long high rpm assault on an obstacle I developed a knock on decel. Pull the valve cover and oil pan and could not figure it out. Could mimic the knock by hand rotating the crank. Pulled the motor and found three flywheel bolts were very loose. The flywheel would rock side to side and make a knocking noise. After pulling the flywheel and putting the engine on a stand I could no longer mimic the knock. Figuring I had found the noise I decided to check the crank bearings and refresh the main seals, oil pan, intake, and exhaust gaskets new oil pump do an egr and vacuum delete and put it back together. Got it back together and it fired right up and the knock was gone but now has a tick at low rpms.

    more clues
    In the oil pan were some pieces of black sealer that had hardened and cracked and fell in to the pan. Also a sliver of thin magnetic metal was in the pan likely from one of two failed fuel pumps. Not sure where else this would come from as all crank bearings were in great shape. During all of the diagnosing the engine was also spun from the camshaft, could this damage the tensioner? At this point I plan to pull the motor and likely replace the entire timing set with an oem set but wanted to get any second opinions. My guess is the chain tensioner is either bad or clogged with a piece of trash.

    Video coming soon.
    Last edited by alk1174; 06-27-2020, 12:46 PM.

    #2
     

    Comment


      #3
      Sounds like a couple of things to me, hard to tell from the video and without being there though. Typical exhaust leak, OR is are valves lash is set correctly? .008 and .012? It's plausible the tensioner is toast and your getting some chain slap.... rally hard to know without pulling the timing cover and looking though.

      Comment


        #4
        Sounds like a bottle of Lucas oil stabilizer is in order.

        Comment


          #5
          Valves were a touch on the tight side, put them back to spec and no difference. Pulled the exhaust and the gasket showed no signs of leakage. Put some copper spray on it and reinstalled it but no difference. It doesn't sound like exhaust and definitely seems to be engine related using the stethoscope.

          Thanks for the responses.

          Comment


            #6
            Could I have jumped timing? With the crank notch at 0. The cam doesn't quite make it the 12 o-clock position . It's been 10 years since I have been this far into one but this seems off. To get the cam to 12 o-clock I have to turn the crank another 15 degrees or better.

            Comment


              #7
              sounds like a burnt valve to me on the video.

              Comment


                #8
                It didn't jump timing. I kept rotating the crank and the sprocket dots and bright links all line up.
                Pulled the timing cover it's a osk timing set and everything looks ok. Guides fully intact, tensioner has preload and moves freely.
                Last edited by alk1174; 06-28-2020, 11:29 AM.

                Comment


                  #9
                  Did you adjust the valves 4 at a time or do them individually based on lobe position? I've had good luck doing them all separately on motors that still sound like a diesel after doing 4 and 4.

                  Comment


                    #10
                    I think I got it. There is a mark on the lower part of the timing cover where the chain is slapping. I assume due to a bad tensioner. I can't think of any other reason for the chain to go slack. I did notice when rotating the crank that at certain points in the stroke the driver side part of the chain would go slack and tighten up on the pass side. I assume due to uneven rotation force on the crank and valve spring tension on the camshaft putting pressure in the reverse direction.

                    Comment


                      #11
                      More clues to the mystery, I pulled the oil filter and it was empty. Held it upside down and couldn't get a single drop of oil to come out. Bad filter causing flow issues? Put an air hose on the passage and only oil came out no trash.
                      Doing a little reading and it seems others have had this issue with bad drain back valves. But I don't think I have ever seen a filter this dry.
                      Last edited by alk1174; 06-28-2020, 03:14 PM.

                      Comment


                        #12
                        Originally posted by alk1174 View Post
                        More clues to the mystery, I pulled the oil filter and it was empty. Held it upside down and couldn't get a single drop of oil to come out. Bad filter causing flow issues? Put an air hose on the passage and only oil came out no trash.
                        Doing a little reading and it seems others have had this issue with bad drain back valves. But I don't think I have ever seen a filter this dry.
                        What filter? I used a mobil1 filter a while back and the dam thing did the same thing (very dry). Had anti leak back diaphram so I figured that's why no oil seeped out when I changed it... turned out to be a bad batch of filters at oreilly's. Swapped with a toyota one and it's been fine. Oil pumps rarely die on the 22r series engines, at least in my experience, so... plus you said you changed it. You also had the pan off not to long ago, so I am sure you would have noticed if the sump screen was clogged up.

                        It is possible I suppose that the tensioner wasn't getting great oil pressure, at least not enough to put tension on the chain. Would be a first for me though.
                        Last edited by flecker; 06-28-2020, 04:08 PM.

                        Comment


                          #13
                          It was a microgard from orielys. Oil pickup was cleaned when i checked the bottom end.
                          My guess is the filter was bypassing flow causing pressure to drop at the tensioner at idle letting the chain slap. As the rpms build the noise gets less to the point I coldnt tell anymore.
                          I am going to do a timing set and headgasket and flush the oil passages and new filter and see what happens.

                          Comment


                            #14
                            I had a tiny bit of RTV clog my tensioner once. Could be some of that loose silicone sealant you found in the pan clogging up god knows what.

                            Comment


                              #15
                              Yip... I have seen what Squamch has mentioned before. If the timing cover is still off, might be worth while to pull the tensioner off and flush it, OR just outright replace it.

                              Comment

                              Advertisement:
                              Advertisement:
                              Advertisement:
                              Advertisement:
                              Advertisement:
                              Advertisement:
                              Advertisement:
                              Working...
                              X