Badgeroo7
New member
- Joined
- Dec 3, 2020
- Member Number
- 3106
- Messages
- 1
Custom Tube Buggy chassis full roller
NO ENGINE, TRANS , OR T-CASE!
Chassis built by Bill Stoy
Brand new aluminum dual pass radiator with -16an fittings welded in
with fan and shroud.
Optima red top battery
trailworthy fab battery box
Led headlight axle mounted
Led rock lights
85 Toyota front axle
2” TG spacers
Trussed
knuckle ball gussets
BTF diff cover
Sold steering stops
Marlin crawler 25mm trunnion upgrade.
Marlin crawler billet hi steer arms
6” tg double ended ram
1650 psi tc pump (can be included)
Psc reservoir, filter and vent all hydro lines are installed and go with buggy.
4 new calipers
4 new rotors
Wilwood master cylinder
Busted knuckle 9:1 pedal assembly
All -3 brake lines installed
4lb residual valves f/r. (Sob stops)
Trail gear hubless hubs
( spare rcv hubs and stock hubs with rcv gear) included
300m Rcv inner and outer front shafts ( lots of rcv spares 300m/4340 and some stock shafts go with)
Brand new ECGS hi pinion front 3rd
5:29
Spool
FJ 80complete front axle goes also
Sherpa 4500 winch mounted to axle
Rear ifs width toyota housing
1” TG wheel spacers
Rear disc break swap
TT disc brake swap brackets
TG diff cover
TG smooth drain plug
5:29 V6 third
Spool
HD 4340 axle shafts ( spare set of 4340 shafts built and ready to go)
17” procompwheels
Longer wheelstuds f/r ( for pass through nuts)
39” reds
110 wheelbase
20” belly
16gallon RCI fuel cell
new Holley 225 pump and hydramat! ( no fuel lines)
TWF RCI tank mount
Brand New Fox 2.0 14” coil overs with reservoirs all 4 corners
Brand new magnitude springs. (Per wizzo and numbers I gave him and rides amazing)
Rear Currie anti rock sway bar with custom swedge tubes( no brittle all thread)
2” wod aluminum lowers front&rear
1.5” wod aluminum uppers front&rear
Fx 7/8x3/4 heims all lowers Rh thread
Fx 3/4 uppers all Rh thread
Procar seats on sliders / I’m 6’4 and have plenty of room. Seats can slide forward enough for for someone 5’7”.
5 point PRPharness
This is a roller!
Add your engine trans and case.
Buggy was completed less than a year ago.
Buggy had
2.4 gm ecotec
904 auto trans
Atlas pass drop tcase.
Will fit 22re trans and cases or many other 4cyl small v6 drivetrains as well.
Asking
$11.5k
( I don’t get on here much reach out at [email protected])
I’ll try and check back here
NO ENGINE, TRANS , OR T-CASE!
Chassis built by Bill Stoy
Brand new aluminum dual pass radiator with -16an fittings welded in
with fan and shroud.
Optima red top battery
trailworthy fab battery box
Led headlight axle mounted
Led rock lights
85 Toyota front axle
2” TG spacers
Trussed
knuckle ball gussets
BTF diff cover
Sold steering stops
Marlin crawler 25mm trunnion upgrade.
Marlin crawler billet hi steer arms
6” tg double ended ram
1650 psi tc pump (can be included)
Psc reservoir, filter and vent all hydro lines are installed and go with buggy.
4 new calipers
4 new rotors
Wilwood master cylinder
Busted knuckle 9:1 pedal assembly
All -3 brake lines installed
4lb residual valves f/r. (Sob stops)
Trail gear hubless hubs
( spare rcv hubs and stock hubs with rcv gear) included
300m Rcv inner and outer front shafts ( lots of rcv spares 300m/4340 and some stock shafts go with)
Brand new ECGS hi pinion front 3rd
5:29
Spool
FJ 80complete front axle goes also
Sherpa 4500 winch mounted to axle
Rear ifs width toyota housing
1” TG wheel spacers
Rear disc break swap
TT disc brake swap brackets
TG diff cover
TG smooth drain plug
5:29 V6 third
Spool
HD 4340 axle shafts ( spare set of 4340 shafts built and ready to go)
17” procompwheels
Longer wheelstuds f/r ( for pass through nuts)
39” reds
110 wheelbase
20” belly
16gallon RCI fuel cell
new Holley 225 pump and hydramat! ( no fuel lines)
TWF RCI tank mount
Brand New Fox 2.0 14” coil overs with reservoirs all 4 corners
Brand new magnitude springs. (Per wizzo and numbers I gave him and rides amazing)
Rear Currie anti rock sway bar with custom swedge tubes( no brittle all thread)
2” wod aluminum lowers front&rear
1.5” wod aluminum uppers front&rear
Fx 7/8x3/4 heims all lowers Rh thread
Fx 3/4 uppers all Rh thread
Procar seats on sliders / I’m 6’4 and have plenty of room. Seats can slide forward enough for for someone 5’7”.
5 point PRPharness
This is a roller!
Add your engine trans and case.
Buggy was completed less than a year ago.
Buggy had
2.4 gm ecotec
904 auto trans
Atlas pass drop tcase.
Will fit 22re trans and cases or many other 4cyl small v6 drivetrains as well.
Asking
$11.5k
( I don’t get on here much reach out at [email protected])
I’ll try and check back here
Attachments
-
1B369FDF-705F-41D0-A2F4-4554157B10B4.jpeg896.1 KB · Views: 87
-
956735CB-6C47-44C6-BAF3-B3D0C0CACC44.jpeg1.2 MB · Views: 55
-
F395B45D-1026-43A0-9834-F86B6250B1F6.jpeg1.2 MB · Views: 59
-
5AD4E009-2368-44D5-A678-8A1A5083107F.jpeg363.1 KB · Views: 68
-
B0394757-CDA6-403B-8DB4-9ECD7A1B6EF0.jpeg1.4 MB · Views: 68
-
IMG_2012.MOV5 MB