vetteboy79
It's bent. #ttb
Nice billet yoke there.
Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
Pinky
- Thread starter Grendel
- Start date
Grendel
Iron Sharpens Iron
- Joined
- May 19, 2020
- Member Number
- 297
- Messages
- 3,535
I no longer use those.
I prefer to replace the coupler on the differential with a standard 1410 yoke now.
WTF is that cancerous link?!?
Grendel
Iron Sharpens Iron
- Joined
- May 19, 2020
- Member Number
- 297
- Messages
- 3,535
LazinessWTF is that cancerous link?!?
. Feel free to pull and post pics not here.
budget76
Thread Killer
found your build's inbred cousin
budget76
Thread Killer
how about a roll of foil tape?
YotaAtieToo
Thick skull
Bunch of sandy manginas in here.
I simply said I didn't like them, they look cheap.
Good thing my opinion doesn't matter, god damn.
It may not matter, but this time it's correct
Grendel
Iron Sharpens Iron
- Joined
- May 19, 2020
- Member Number
- 297
- Messages
- 3,535
That's the beautiful thing, until someone sends me a check, it's mine to do what I want with.It may not matter, but this time it's correct
So, send a check for it, or STFU.
Grendel
Iron Sharpens Iron
- Joined
- May 19, 2020
- Member Number
- 297
- Messages
- 3,535
Building headers... then windshield, brush the aluminum and apply a matte clear wrap with the graphics.
Have different rims and tires for it, will be completely outside the body.
Have different rims and tires for it, will be completely outside the body.
Attachments
WaterH
Well-known member
Looking good. I really like the wide band below the windshield. It gives it a sporty short windshield while still blocking the wind. Was that stock? Got to say the whole thing looks way more sporty than a Jeep.
Nitpic, what’s going on where the hood meets the grill by the fender?
Nitpic, what’s going on where the hood meets the grill by the fender?
That fits just like factory. At least, my CJ2A looked just like that. The gap kinda tightened up when you engage the springy hood latches.
ANGRYBLACK
Well-known member
Once again Brother you are nailing it!!!!
Grendel
Iron Sharpens Iron
- Joined
- May 19, 2020
- Member Number
- 297
- Messages
- 3,535
Thanks brother.
Doing all the little shit bug fixes in the first 300miles, sucks.
Like GM didn't put a dipstick on truck based 8L90E's and has a dealer only fluid check/fill tool. Fuck that, B&M makes a dip stick. It's on the way.
This fucking thing is scary.
WaterH
Well-known member
300 miles? I’ve got 2000 miles on my project and still working out bugs. How about some outside pics?
Grendel
Iron Sharpens Iron
- Joined
- May 19, 2020
- Member Number
- 297
- Messages
- 3,535
budget76
Thread Killer
I look forward to seeing it on snow tires
Opiebennett
XJ_Ranger
Stolen Valor? Or a friend of yours?
WaterH
Well-known member
Do you have a pic of the inside showing how you did the wipers. Wipers were a big problem on my build. Looks like they could even be more of a pain on your folding windshield. (Unless there’s some kind of stock setup)
Grendel
Iron Sharpens Iron
- Joined
- May 19, 2020
- Member Number
- 297
- Messages
- 3,535
Electric boat.
Uhhh..... Make some?
WaterH
Well-known member
I did a lot of research and found C4 corvette seats are known to be the most comfortable of Corvettes. I got some for my truck and I love them. They are very low and I can confirm they are very comfortable. The only seats that I know of that are lower are the ones in my Delorean, but they are not comfortable. I’m seriously considering switching them to C4 seats. (They might be too tall for that car.)
I would have to go back through your thread, but I thought you allready had your seats. If so, the C4 mounts/sliders might work. They are low, but probably they only work with the C4 seats. If you don’t have the seats yet, you should sit in a C4 to judge. They would look great in Pinky.
budget76
Thread Killer
is the Willys plate from Eshan?