Bend-Tech EXH Module
Zoom image

Bend-Tech EXH Module


Not rated yet

The Bend-Tech EXH is specially designed to aid in the manufacture of exhaust tubing/pipe.

The main interface of Bend-Tech EXH gives you the ability to re-create the critical components of a vehicle (axles, mufflers, gas tanks, etc) and then properly route the tubing around them. This interface also allows you to create multiple bent and straight tubes within the same design. You can then obtain the cutting/bending instructions for each tube.

The interface is easy to use, using a grid with directions related to a vehicle and a built-in offset tool for avoiding obstacles.

Also included in EXH are several other part designers, including dozens of Templates, Custom Part (LRA), Custom 3D Part, Sketch 2D/3D.

  • $150.00
Qty:  

EXH Features:

3D Parts & Components

Design and create exhaust tubes around axles, mufflers, gas tanks, and etc. Then the software will provide necessary bending instructions such as length, rotation, and angles, of the tubes with accurate exhaust tube bending and fabricating.


Bend Calculation Output

Software will provide cut length, bend locations, bend angles, and rotations of your created parts for accurate bending/fabrication. Each bend location is based from the end of the tube.


Parts Wizard

Create 3D objects with custom dimensions such as mufflers, axles, tires, and etc. Once created, these objects can be placed inside main 3D environment for accurate exhaust tube routing.


Flat Layout

Obtain/Print flat layout of designed parts. Users can choose which part of the bend they wish to mark (Start/Center/End), along with rotations, angles, spring angles, and CLR display options.


Bending Simulation

Simulation helps the fabricator visualize the bending process before running the part through the machine. This helps to confirm the manufacturability of the part and the bend order. (*Does NOT check for collision.)


Designer: Sketch 3D
  • Click-and-sketch part creation in 3D.
  • Adjustable grid-snapping.
  • Sketch then adjust dimensions.
  • Easy switching between XYZ planes.

Designer: Sketch 2D
  • Click-and-sketch part creation.
  • Adjustable grid-snapping.
  • Sketch then adjust dimensions.
  • Simple, easy-to-use 2D design.

Designer: Custom Part 3D

The Custom 3D Part interface allows you to enter the definitions of your part in a sequence following the center line of the material. Directional terms are easy to understand for creation of the part. These terms are; left, right, front, back, ceiling, and floor. The bend angles and rotations are automatically calculated.


Multiple Dies for Single Part

Define a part with size definitions for each individual bend.


Designer: Custom Part

Create a part by starting at one end and entering the distance between bends, rotations between bends, and the angle for each bend. The length values can be apex or tangent values.


Designer: Templates

Choose from dozens of predefined templates. The templates are easy to use and in seconds you will have your design completed and be ready to start bending.


Post Bending Cutoff

Cutoff allows extra material to be added at the end of the tube for cutting after bending. The cut length and bend locations are automatically adjusted for cutoff values.


Bend-Tech software requires an active internet connection in order to activate the license on your computer, and then every 6 months after.

This module requires latest version of PRO or SE.

Minimum Requirements:

  • Windows Operating System (XP, Vista, 7, 8, 8.1, 10)
  • 1 GHz Processor
  • 2 GB RAM (Memory)
  • 1 GB Hard Drive Space
  • 1024 x 768 Screen Resolution
  • OpenGL 1.3 Compatible Graphics Card
  • .NET Framework 3.5 Installed
  • Active Internet Connection (Internet connection is needed during the first activation and then every 6 month, software can run offline in between.)

Recommended Requirements:

  • Windows Operating System (7, 8, 8.1, 10)
  • 1GHz Dual-Core Processor
  • 4GB Ram (Memory)
  • 1 GB Hard Drive Space
  • 1280 x 800 Screen Resolution or greater
  • OpenGL 1.3 Compatible Graphics Card
  • .NET Framework 3.5 SP1 Installed
  • PDF Reader Installed (for Help Guides)
  • Full Keyboard and Mouse
  • CD Drive (for install from CD)
  • High-Speed Internet

MacOS Requirements:

  • Windows OS running on Emulator/Parallels. (e.g.: Boot Camp, Parallels, and VMware.)
  • Same requirements as above.
  • Bend-Tech does NOT run directly on MacOS.
    • SKU
      bendtechEXH-Module
  • Type
    Module, Standalone
Customer reviews
Please sign in to add review
There are no comments yet. Be the first to leave a comment
Related products
Customers who viewed this product bought